KTS 520 and KTS 550 – for multipurpose diagnosis using existing workshop hardware

KTS 520 – the multipurpose solution geared to automotive workshops
· Suitable for workshops that only occasionally require control unit diagnosis data
· Multipurpose diagnosis possible using a PC or a laptop
· Equipped with a multimeter for voltage, resistance and current measurements

KTS 520 Technical Data

Diagnosis protocol:
Connections for
ISO 9141-2,K/L lines
Flasher code
SAE-J1850 DLC (GM,…)
SAE-J1850 SPC (Ford)
CAN ISO11898 ISO 15765-4 (OBD)

Multimeter:
Accuracy 1% of measured value
Voltage, minimum resolution: 0.1 mV, maximum measuring range: 200 V
Current, minimum resolution: 0,1 mA, maximum measuring range: 600 A resistance, minimum resolution:
100 mOhm, maximum measuring range: 1 M Ohm

Connections for:
OBD line or via universal adapter plus vehicle spezific cables
Multimeter socket yellow (+), blue (-) and black (ground), USB, serial,
Power supply and status indicator

KTS 520 and KTS 550 – common technical features
· Simple adaptation to laptop or PC through USB or serial standard interface
· Powered by ESI[tronic]: ideal in combination with the workshop software for fast and targeted
vehicle diagnosis in the workshop
· Full range of ESI [tronic] test specification immediately available

· Both models are equipped for all current diagnosis protocols:
– ISO systems of European vehicles
– SAE systems for American and Japanese vehicles
– CAN protocols for testing state-of-the-art
CAN bus systems in new vehicles
· direct multiplexer connection via OBD line to the diagnosis socket
· software automatically controls multiplexer – thus dispensing with need for troublesome changing around of communication connections

KTS 550 – the multipurpose solution for automotive workshops
· Workshop PC or laptop together with ESI[tronic] provides a test station for convenient vehicle diagnosis
· 2-channel multimeter for rapid tracing of faults through simultaneous measurements on two components
· 2-channel oscilloscope for complicated tests on state-of-the-art vehicle-system components – ideally suited for sensor testing in vehicle, e.g. simultaneous display of both lambda sensors in a single display image
· One device for both diagnosis and measuring technology

KTS 550 Technical Data

Diagnosis protocol
ISO 9141-2,K/L lines

Flasher code
SAE-J1850 DLC (GM,…), SAE-J1850 SPC (For d)
CAN ISO11898 ISO 15765-4 (OBD)
2-channel multimeter Accuracy 1% of measured value
Voltage, minimum resolution: 0.1 mV, maximum measuring range: 200 V
Current, minimum resolution: 0,1 mA, maximum measuring range: 600 A
resistance, minimum resolution: 100 mOhm, maximum measuring range: 1 M Ohm
2-channel oscilloscope 1-channel operation: 1x 100 K scans/sec
2-channel operation: 2x 50 K scans/sec
Channel 1 zero potential
Connections for OBD line or via universal adapter plus vehicle spezific cables
Multimeter channel 1: socket yellow (+), blue (-), channel 2: red (+) and black (ground), USB, serial, power supply and status indicator

Ideal augmentation to PC-aided testers
· Extension of diagnosis options, e.g. for the Emission System Analysis (ESA) or for rival devices with standard interface

· In such an instance the following
PC requirements must be fulfilled: operating system Win95 to Win2000, minimum of 128 MB main memory, one free USB and one serial interface, minimum of 5 GB hard drive capacity for the ESI[tronic]- basic installation

Simple connection to vehicle

Simple connection to vehicle
More car diagnostic tool like ELM327 , you also can visit the blog www.x431us.com

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s